Paver Calculator

Enter the patio or walkway size, pick a paver and a pattern, and get the paver count plus the base gravel and bedding sand that go under it.

1

Measure the patio or walkway

Area 1

168 sq ft

Odd shape? Split it into rectangles, circles and triangles and add each one.

2
3

Base and sand What goes under the pavers

Base is crusher run at 1.50 t/yd³ plus 15% for compaction. Joint sand coverage is printed on the bag and depends on joint width and paver thickness.

You need

471 pavers

168 sq ft + 5% · 2.67 per sq ft

Base gravel
3.58 tons
2.39 yd³
Bedding sand
0.77 tons
0.57 yd³ · 31 bags of 50 lb
Joint sand
5 bags
Paver area
176 sq ft

Cost

Enter prices to see the total.

How to calculate pavers

Work out the square footage of the patio, add waste for the pattern you are laying, then divide by the area of one paver. The base and bedding sand are separate orders: both are a layer of the same area at a set depth.

pavers = sq ft × (1 + waste %) ÷ (paver length × width in inches ÷ 144)
base = sq ft × base depth (in) ÷ 324 × 1.15 yd³ · sand = sq ft × 1 ÷ 324 yd³

Example: a 12 by 14 ft patio in 6 × 9 pavers

168 sq ft + 5% = 176.4 sq ft. A 6 × 9 paver covers 0.375 sq ft, so you need 471 pavers. Underneath: 2.39 yd³ of crusher run (about 3.6 tons) for a 4 inch base, and 0.57 yd³ of bedding sand (about 31 bags of 50 lb).

Pavers per square foot by size

Paver sizePer sq ftPer 100 sq ft + 5%Per 100 sq ft + 15%
4 x 8 in (brick, Holland)4.50473518
6 x 6 in4.00420460
6 x 9 in2.67280307
12 x 12 in1.00105115
16 x 16 in0.566065
12 x 24 in0.505358
24 x 24 in0.252729

Waste by laying pattern

PatternExtra to order
Running bond or stack5%
Basket weave5%
Herringbone, 90°10%
Herringbone, 45°15%
Curves, circles, many cuts15%

Herringbone at 45 degrees needs a cut paver at every edge, which is where the extra goes. Patterns that run parallel to the edges waste the least.

Paver base and sand

ProjectBase depthBase per 100 sq ftBedding sand per 100 sq ft
Patio or walkway4 in1.42 yd³ · 2.13 t0.34 yd³ · 19 bags
Patio on clay or wet soil6 in2.13 yd³ · 3.19 t0.34 yd³ · 19 bags
Driveway8 in2.84 yd³ · 4.26 t0.34 yd³ · 19 bags
Base includes 15% for compaction, sand 10%.

Use crusher run or a dense-graded base with fines for the base, compacted in 2 to 3 inch lifts. Use coarse concrete sand for bedding, not fine mason or play sand. The gravel calculator and sand calculator work for other base and sand jobs.

Paver calculator questions

How many pavers do I need per square foot?

Divide 144 by the paver length × width in inches. 4 × 8 pavers: 4.5 per sq ft. 6 × 6: 4. 6 × 9: 2.67. 12 × 12: 1. 16 × 16: 0.56. Nominal sizes include the joint; check the per-square-foot figure the manufacturer prints, which can be slightly higher.

How much base do I need under pavers?

Typical guidance from paver manufacturers and the Interlocking Concrete Pavement Institute is 4 to 6 inches of compacted crushed stone base for patios and walkways and 8 to 12 inches for driveways, more on clay or wet soil. Add 15 percent: the base compacts as you plate it.

How much sand do I need for pavers?

A 1 inch layer of coarse concrete sand for bedding, screeded flat over the base. That is about 0.3 cubic yards per 100 sq ft, or 19 bags of 50 lb with 10% extra. Joint sand (polymeric or fine sand) goes on after the pavers are laid; the bag says how many square feet it covers.

How much extra pavers should I buy?

5 percent for a straight running bond or basket weave, 10 percent for 90 degree herringbone and 15 percent for 45 degree herringbone, circles or lots of curves. Keep a few spares from the same production lot for future repairs; colors vary between lots.

Do I need edge restraint?

Yes, on every edge that is not against a wall or curb. Buy edge restraint by the perimeter length in feet, plus a spike every 12 inches or so.

Other material calculators